Feature Description
》Two phase two sets of contact with 100A switching capability
》Very minimal power consumption from the coil
》Load lead-out mode: 1 input 2 output, 3 input 4 output
》4KV dielectrics strength coil to contact
》IEC-62055-31 UC3 compliant
》Outline dimensions(63×34×21)mm
》RoHS compliant
| Contact Data | |
| Rated load(FLA) | 100A/250VAC |
| Contact form | 2A & 2B |
| Contact material | AgSnO2 |
| Initial contact resistance | 2mΩ（0.1A@6vdc） |
| Max.switching current | 100A |
| Max.switching voltage | 250VAC |
| Max.switching power | 25000VA |
| Electrical endurance | 1x104 ops |
| Mechanical endurance | 1x106 ops |
COIL POWER | ||
| Coil type | Pulse duration | Power consumption |
| Single | Min.50ms | 3W |
| Dual | Min.50ms | 6W |
CHARACTERISTICS | ||
| Insulation Resistance | 1000MΩ（at 500VDC) | |
Dielectric Strengt | Coil To Contact | 4000VAC 1 min |
| Across Open Contact | 2000VAC 1 min | |
| Operate Time | Max.20ms | |
| Release Time | Max.20ms | |
| Shock Resistance Functional | 100m/s 2(10g) | |
| Shock Resistance Destructive | 1000m/s 2(100g) | |
| Ambient Temperature | -40～85℃ | |
| Humidity | 98%RH, +40℃ | |
| Vibration Resistance | 10-55Hz, 1.5mm(DA) | |
| Termination | PCB | |
| Unit Weight | 110g | |
| Construction | Dust Protected | |
COIL DAT | |||||
| Nominal coil voltage | 6Vdc | 9Vdc | 12Vdc | 24Vdc | |
| Operating Voltage VDC | ≤4.2 | ≤6.3 | ≤8.4 | ≤16.8 | |
| Coil Resistance (Ω±10%)@23℃ | Single coil resistance | 12Ω | 27Ω | 48Ω | 192Ω |
| Dual coil resistance | 2×6Ω | 2×13.5Ω | 2×24Ω | 2×96Ω | |
Ordering Information
Dimensions (mm)
Precautions
1. All relays must be shipped in the closed state. The relay may become open during shipping or assembly, therefore, it is recommended to set the relay state to off through the power supply.
2. In order to keep the relay in the open or closed state, the coil voltage needs to reach the rated voltage, and the electronic pulse needs to be 5 times the working time to ensure the correct state conversion. Do not apply voltage to T1, T2, and T3 on the coil for more than one minute to prevent the coil from being damaged.
3. The relay has polarity distinction. If the polarity required by the user does not match the data, it should be specially mentioned when ordering.
4. Relays should be handled with care when entering the factory for inspection and use to prevent damage from affecting parameters. Products entering the factory for destructive inspection must be strictly differentiated from normal products and must not be installed and used.
If you are interested in our products, or have any questions about our products, please feel free to contact us, we will serve you wholeheartedly
Huajin Technology Jiaxing Co., Ltd.
Email: alio@hj-relay.com
Phone: 18857397300
Address: Huangqiao Industrial Park, Yanyu Highway, Haiyan County, Zhejiang Province
Copyright © All rights reserved by Huajin Technology Jiaxing Co., Ltd.
Huajin Technology